The Magma is hand built for highest efficiency. The design stops the current leakage and reduces the heat build up.
It will produce 1 liter of HHO at 10 amps or 10 watts per ML and at 15 amps will produce 2 liters of HHO at 7.5 watts per ML. 

Order this unit if you already have a constant current PWM and an EFIE or Optimizer Tuner. These are required to achieve 50% to 100% gains in fuel mileage.

If you need the complete kit to install see below:

We offer a high output Stanley Meyer version with EIGHT SS Cells in a rugged six inch diameter schedule 40 case. Output is close to 4 to 6 liters/minute on this high output unit when using a Dave Lawton design PWM.  The case is NOT CLEAR as pictured in photo. The clear acrylic cases did not stand up to shipping and handling so we no longer offer the clear case.

These generators are built to exacting standards using the finest 316L Seamless Stainless Steel tubes that have approx 1.2mm clearance for highest efficiency and lowest amps. There is no heat buildup as these units run cool to barely warm.

Each cell is tapped for nylon screws to maintain perfect spacing between the inner and outer tubes of approx 1.5 mm.

Cells are wired in series for highest efficiency, ie. Highest HHO output for lowest amperage draw.

Units require NO ELECTROLYTE!…just distilled water so there is no danger to the aluminum parts of your engine. However, our testing shows that using KOH electrolyte increases output. This is the ONLY unit we know of that will produce HHO using tap water.

Units must be used with our Stanley Meyer PWM (see below) that is included with this system.

Dimensions: Approximately 6 to 7 inches in diameter by 26 inches tall

Pricing: 8 cells 15" tall for $1645 + $155 S&H  

Please allow at least three weeks for completion plus five days for shipping time. We cannot ship overseas as this unit is too heavy for economical shipping outside the USA

WE WILL NOT SHIP THIS UNIT OUTSIDE DOMESTIC UNITED STATES

1. When the edges of the plates of a hho generator are submerged in the water/catalyst bath a great deal of the electrical current passes through the edges of the plates. This current is largely wasted in terms of HHO production. When the edges are outside of the bath, as with the hho dry cell, all of the current is forced to travel directly to the faces of the plates. Therefore all of the current supplied to the hho generator is utilized in efficiently making HHO gas.

This is the main reason the hho dry cell design has become so popular.

2. The electrolyte bath attacks and will eventually destroy the electrical connections if they are submerged. With the hho dry cell design they are outside of the water/catalyst solution which is stored in a separate reservoir and recirculated by the hho dry cell, this help in producing more hho gas and less heat (steam)

The plates of our HHO dry cells are made of 316L stainless steel. This has been found to have the best properties of resistance to attack from the process of electrolysis. However, mounting hardware and wire and cable are very difficult to find in 316L grade and are very costly to use.

Therefore copper cable is usually used by Hydrogen on Demand installers when installing their hho generators. And a lower grade of stainless steel nuts and bolts are used by hho generator builders for assembly and when these are submerged in the electrolyte, they rapidly get eaten away.

With the HHO dry cell design, all of these connections are outside of the electrolyte so this isn't an issue.

Why is it that a hho dry cell design produces more hho gas?

Because it is efficient, there is not a lot of wasted spaced and electrolyte solution that is not being used and charged with current. The very small volume of electrolyte solution that enters the hho dry cell is subjected to electrical current and able to react and create hho, then exit the hho dry cell generator and recirculate.

Why do hho dry cells run cooler than other hho generators?

Again, because of the design of the hho drycell, with the "wet cell" generators the heat created by the electrolysis process has no place to go. With the Dry Cell Design the electrolyte solution is gravity fed in order to keep it replenished. A constant flow keeps the unit from overheating.

This Dry Cell is one of the most effective on the market today.

The most used hho dry cell in Europe and USA

The HHO Dry Cell design shown below has about 80-90% total efficiency when all things are considered (ambient temperature, ambient pressure, accurate measurement of gas volume and current) when powered by straight DC. Pulsing or modulation of the input voltage waveform to this hho dry cell could increase the performance further, as it is known that in the beginning of each pulse larger current flows than in the steady state condition, thus lowering the cell voltage needed to push threw a certain amount of current and increasing the efficiency of a Hydrogen Generator slightly.

Thousands of satisfied customers stand behind these hho dry cells.

Why is the 11 plate hho dry cell the "best" hho dry cell design ?

I do not claim to know everything there is to know about Electrolysis, but the lowest "theoretical" voltage for electrolysis is understood to be 1.24 volts and if you don't go over 1.48 volts the electrolysis chamber (cell) will remain cool - similar to the environment you have it in, if you do go over 1.48 v you are producing heat.

So there comes a point at which you must trade some of your energy to produce heat in order to get the desired hho gas output.

The 11 plate hho dry cell has a total of 10 separate cell chambers, divide by an additional Positive plate the arrangement of the plates and the hole configuration is what has proven to be the dry cell design that produces the most hho gas with the least amperage draw

Conclusion : For the Novice Mechanic wanting to experience the benefits of of adding hho gas to their vehicle by installing an hho generator this design is the way to go. To Install Hydrogen on Demand On The Average Car or Truck This is the Best HHO Generator to start with.

This HHO Dry Cell Design Produces clean hho gas at low amp draw, you chose the hho dry cell, or cells that best suit your engine size. Extensive testing has been ongoing for years as to how much hho gas is needed for optimal results on the average motor vehicle. According to NASA and other test, including ours and other hho installers 5% of the fuel mix is all you need. This works out to be Apx. 1/4 to 1/2 LPM ( liter per minute ) of hho gas per Liter of motor size.

I will publish a more detailed article on this subject and add a link for those who want to do more research.

European countries are catching on to the awesome effects hho generators and Hydrogen on demand systems can have on there autos and trucks. We are proud to say our hho drycell is producing awesome results in Greece, Netherlands, Italy, France, and all over Europe as well as all over Australia.

Install - our 11 plate dry cell system on a 1600cc auto using petrol resulted in 52% increase in gas mileage and near 90% lower emissions.

These "HHO Generators", will produce Hydrogen and Oxygen gas commonly known as Brown's gas or HHO.

Hydrogen is a volatile colorless gas that has a low temperature ignition point. This gas also has no smell. Serious injuries and bodily harm can occur if the device is not handled or used properly! Powergate Technologies accepts no responsibility for your health or safety when working with hydrogen gas or any of our products. You are 100% responsibility to follow all safety precautions. Since we are not attorneys we recommend you research out correct safety and handling procedures before using any of our equipment.

Please read our "Terms of use page"

Please, Safety First when dealing with any hydrogen generators!

11 cell hho dry cell - Tested hho dry cell kit 11 cell hho dry cell - Diy hho dry cell kit 11 cell hho dry cell - Complete hho dry cell kit - install

You Will No Doubt Run Across other hho generator sites selling The Same Type of HHO Dry Cell and HHO Dry Cell Kits. This 4x4 hho generator is the most copied out there. As everyone is searching for a compact hho generator that will produce the right amount of hho gas needed at low amp draw.

Our staff have purchased and constructed many water gas generators. We've researched what makes the Stanley Meyer hydrogen generator superior over common hydrogen generators that use the electrolytic process to make Brown's gas.

We believe this HHO Dry Cell Design is the best hho generator available at these prices.

You can be overwhelmed by the different hho generator designs, sizes and shapes once you start studying this awesome yet simple hydrogen on demand technology.

* Our Excellent Customer Service. Calls are welcome! Call 949-945-5417.